CUTTING NOZZLES FOR OXY-CUTTING CARS

Kategori: Cutting Nozzles for Mechanical Torches in Torch Car

CUTTING NOZZLES FOR OXY-CUTTING CARS

AOG DR & AOG DR-91 CUTTING NOZZLES

Most widely used nozzle for oxy-cutting car and emergency cutting torch. Premixing technology allows best and homogeneous mixing of gas and oxygen to give high thermal power. Built in copper. Directly connected to cutting torch by screwing. Single heating.

Note: To cut stainless steel AOG and AOG 91 cutting nozsles are used. For details please get in touch with us.

Where to use : AOG DR: ALBACUT/6, ALBACUT/7,  B/87 and  AOG DR-91: ALBACUT/6-91, ALBACUT/7-91, B/87-91

What to cut : Billet, bloom, beam blank, slabs up to 500 mm thickness

Cutting speed : High, süpersonic

Heating capacity : High

Kerf  : Very low down to 3 mm

Flashback : Very low probability

Nozzle life : Long

Tip-piece distance: 100-140 mm

Cleaning of nozzle : By nozzle cleaning picks

HSC/HSI CUTTING NOZZLE

Fastes nozzle for oxy-cutting car and emergency cutting torch. Premixing technology allows best and homogeneous mixing of gas and oxygen to give high thermal power. Built in copper. Directly connected to cutting torch by screwing. Triple heating with etreme thermal power. Fastes nozle of the world. 25% faster.  Cuts from up to 180 mm (+40 mm) from the piece as a result it is less affected from splash and heat. So life of torch and nozzle are extended . HSI nozzle for stainless steel and HSC for carbon steels and alloyed steels. 

Where to use : ALBACUT/HS, B/87-HS

What to cut : Billet, bloom, beam blank, slabs up to 1000 mm thickness

Cutting speed : Very High, süpersonic

Heating capacity : Very High, triple heating

Kerf  : Very low down to 3 mm

Flashback : Very low probability

Nozzle life : Long

Tip-piece distance: 140-180 mm (+40 mm more)

Cleaning of nozzle : By nozzle cleaning picks

MSC/MSI CUTTING NOZZLE

New design nozzle for oxy-cutting car and emergency cutting torch. Premixing technology allows best and homogeneous mixing of gas and oxygen to give high thermal power. Built in copper. Directly connected to cutting torch by screwing. Double heating with high thermal power.  Cuts from up to 180 mm (+40 mm) from the piece as a result it is less affected from splash and heat. So life of torch and nozzle are extended . MSI nozzle for stainless steel and MSC for carbon steels and alloyed steels. 

Where to use : ALBACUT/MS, B/87-MS

What to cut : Billet, bloom, beam blank, slabs up to 800 mm thickness

Cutting speed : Very High, süpersonic

Heating capacity : Very High, Double heating

Kerf  : Very low down to 3 mm

Flashback : Very low probability

Nozzle life : Long

Tip-piece distance: 140-180 mm (+40 mm more)

Cleaning of nozzle : By nozzle cleaning picks

TFT CUTTING NOZZLE

Cutting of up to 2000 mm extreme thickness ferrous material. Put in water cooled copeer nozzle head.  Built in copper.

Where to use : ALBACUT/TFT cutting torch

What to cut : Extreme thickness scarp, steel, cast iron, ladle skul, tundish skul.

Cutting speed : High supersonic

Thermal capacity : High

Kerf  : Low

Flash back : Low possibility

Nozzle life : Very lng

DBN  NOZZLE FOR DEBURRING TORCH
 For laminar flow of oxygen to get rid of bur from the bottom of billet/bloom during oxcutting. Built in copper.

Where to use : For ALBASAC deburring torch built on Oxy-cutting car

ASH DEDURRING HEAD

For slab scarfing, Built in copper. Completely water cooled